Actual offers of Ball joint VW Multivan T6 2.0 TSI 4motion 204 hp Petrol CJKA
- Fitting Position: both sides, Lower, Front Axle
- Cone Size [mm]: 15
- Packing Type: Box
- Item number: 2462S0072P
- Manufacturer: RIDEX PLUS
- EAN number: 4059191997756
- Condition: New
- Fitting Position: both sides, Lower, Front Axle
- Cone Size [mm]: 15, 18,2
- Cone Pitch: 1:6
- External Thread [mm]: M14x1,5
- Packing Type: Box
- Item number: 2462S0072
- Manufacturer: RIDEX
- EAN number: 4059191326600
- Condition: New
- Fitting Position: Front axle both sides
- Cone Size [mm]: 18,30
- Thread Size: M14x1.5
- only in connection with: 2 x M12
- Hole Pitch 1 / Hole Pitch 2: 77,00mm
- Item number: 2462S0175
- Manufacturer: RIDEX
- EAN number: 4059191417292
- Condition: New
- for PR number: 1BA, 1BB, 1BJ, 1BQ, 1BV, 2MD, 2MF, 2MG, 2MH
- Fitting Position: Front Axle, Lower, both sides
- Cone Size [mm]: 18.3
- Diameter [mm]: 41.35
- External Thread Size: М14х1.5
- Item number: 22-PW-17
- Manufacturer: MOTOTECHNIKA
- EAN number: 22-PW-17
- Condition: New
- Fitting Position: Front Axle
- Cone Size [mm]: 18,2
- Required quantity: 2
- Item number: RH03-0017
- Manufacturer: REINHOCH
- EAN number: 5901655167184
- Condition: New
- Fitting Position: Front Axle Left, Front Axle Right
- Cone Size [mm]: 18,1
- External Thread [mm]: M14x1,5
- Supplementary Article / Supplementary Info Info 2: with nut
- Item number: M-S0193
- Manufacturer: MERTZ
- EAN number: 5902701001889
- Condition: New
- Fitting Position: Front Axle, Lower
- Cone Size [mm]: 18
- for OE number: 7H8 407 361
- Supplementary Article / Supplementary Info Info 2: with bolts / screws
- Item number: 9040148
- Manufacturer: KAMOKA
- EAN number: 2218515501418
- Condition: New
- Fitting Position: Front Axle Left, Front Axle Right, outer
- Cone Size [mm]: 18
- Diameter [mm]: 41,6
- Weight [kg]: 0,496
- Thread Size 1: M14X1,5 RHT
- paired article number: 220416
- Item number: 220416
- Manufacturer: A.B.S.
- EAN number: 8717109355499
- Condition: New
Important: Observe Fitting Instructions
- Fitting Position: Lower, Front Axle, Front Axle Left, Front Axle Right
- Cone Size [mm]: 15
- Mounting Type: Bolted
- not for payload [kg]: 3200
- Packing Type: Box
- Packaging length [cm]: 12,5
- Packaging width [cm]: 9
- Packaging height [cm]: 8
- Item number: VO-BJ-1990
- Manufacturer: MOOG
- EAN number: 4044197252060
- Condition: New
-
- Fitting Position: outer
- not for payload [kg]: 3200
- Fitting Position: Lower, Front Axle, Front Axle Left, Front Axle Right
- Required quantity: 2
- Weight [kg]: 0,700
- Flange Hole Diameter [mm]: 41,4
- Packaging length [cm]: 13,5
- Packaging width [cm]: 9,5
- Packaging height [cm]: 7
- Item number: L29578
- Manufacturer: MONROE
- EAN number: 5412096440762
- Condition: New
- Fitting Position: Front Axle
- Cone Size [mm]: 18,1, 22,1
- Thread Size: M14 x 1.5
- Mounting points diameter [mm]: 13
- Item number: 80393AL
- Manufacturer: ALTE AUTOMOTIVE
- EAN number: 225627216152972161529
- Condition: New
- Fitting Position: Front Axle, Lower
- Cone Size [mm]: 18
- for OE number: 7E0407361
- Supplementary Article / Supplementary Info Info 2: with bolts / screws
- Item number: 9040151
- Manufacturer: KAMOKA
- EAN number: 2218515501421
- Condition: New
- Fitting Position: Front Axle, outer, Left, Right, Lower
- Thread Size: M14x1.5
- Length [mm]: 105
- Height [mm]: 95
- Width [mm]: 55
- Item number: TC2089
- Manufacturer: DELPHI
- EAN number: 5012759353806
- Condition: New
- Supplementary Info: EXPERT KITS +
- Fitting Position: Front Axle
- Cone Size [mm]: 22
- Weight [kg]: 0,488
- Packaging width [cm]: 9,5
- Packaging height [cm]: 7
- Packaging Depth [cm]: 13
- Item number: V10-0682
- Manufacturer: VAICO
- EAN number: 4046001360688
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Fitting Position: Front Axle Left, Front Axle Right
- Cone Size [mm]: 22
- External Thread [mm]: M14x1,5
- Supplementary Article / Supplementary Info Info 2: with nut
- Item number: M-S0722
- Manufacturer: MERTZ
- EAN number: 5902701025830
- Condition: New
- Fitting Position: Front Axle Right, Front Axle Left
- Thread Size: RHT M14x1,5
- Length [mm]: 77
- Thread Size 1: RHT M14x7,5
- Base body material: Cast Iron
- Net weight [kg]: 0,65
- Item number: G30.7324
- Manufacturer: OMG SRL
- EAN number: 590410080586
- Condition: New
-
- for vehicles with gross vehicle weight [t]: 3,0
-
- for vehicles with gross vehicle weight [t]: 2,8
-
- for vehicles with gross vehicle weight [t]: 2,6
- Fitting Position: Front Axle Left, Lower, Front Axle Right
- Supplementary Article / Supplementary Info: with lock nuts
- Weight [kg]: 0,449
- for OE number: 7H0 407 361 A
- Control / Trailing Arm Type: for control arm
- Mounting points diameter [mm]: 13
- Hub fastening hole diameter [mm]: 41,5
- External Thread Size: M14 x 1,5
- Cone Size 1 [mm]: 18
- Cone Size 2 [mm]: 21
- Item number: 23336
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816233367
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Fitting Position: Lower, Front Axle Left, Front Axle Right
- Cone Size [mm]: 18,3
- External Thread [mm]: M14x1,5
- Weight [g]: 650
- Hole Spacing [mm]: 80
- Item number: 130025
- Manufacturer: DAKAtec
- EAN number: 4250745532311
- Condition: New
- Fitting Position: Lower, Front Axle Left, Front Axle Right
- Cone Size [mm]: 18,0
- Diameter [mm]: 41,0
- External Thread [mm]: M14x1,5
- Weight [g]: 750
- Hole Pitch 1 / Hole Pitch 2: 80mm
- Item number: 130148
- Manufacturer: DAKAtec
- EAN number: 4250745519848
- Condition: New
- Supplementary Info: EXPERT KITS +
- Fitting Position: outer, Lower Front Axle
- Weight [kg]: 0,569
- Packaging width [cm]: 9,5
- Packaging height [cm]: 7
- Packaging Depth [cm]: 13
- Item number: V10-7185-1
- Manufacturer: VAICO
- EAN number: 4046001287824
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- 1
- 2
- 3
- 4
- 5