Actual offers of Suspension arm RENAULT Clio IV Van 1.2 16V 75 hp Petrol D4F 722
- Fitting Position: Lower, Front Axle Left
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- Length [mm]: 329,5
- Cone Size [mm]: 18
- Trim Level: EXC. 1.6 RS
- Rod / Strut: Push Rod
- Item number: 273C1145
- Manufacturer: RIDEX
- EAN number: 4059191820795
- Condition: New
- Fitting Position: Lower, Front Axle Right
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- Length [mm]: 329,5
- Cone Size [mm]: 18
- Inner Diameter [mm]: 12,2
- Trim Level: EXC. 1.6 RS
- Rod / Strut: Push Rod
- Item number: 273C1142
- Manufacturer: RIDEX
- EAN number: 4059191820733
- Condition: New
- Supplementary Info: Original VAICO Quality
- Fitting Position: Right, Lower Front Axle
- Control / Trailing Arm Type: Control Arm
- paired article number: V46-0115
- Supplementary Article / Supplementary Info Info 2: with ball joint
- Weight [kg]: 4,85
- Axle alignment required after fitting
- Article number of the recommended special tool: V99-1020
- Packaging width [cm]: 9,3
- Packaging height [cm]: 34,1
- Packaging Depth [cm]: 23,5
- Item number: V46-0114
- Manufacturer: VAICO
- EAN number: 4046001372803
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Supplementary Info: Original VAICO Quality
- Fitting Position: Left, Lower Front Axle
- Control / Trailing Arm Type: Control Arm
- paired article number: V46-0114
- Supplementary Article / Supplementary Info Info 2: with ball joint
- Weight [kg]: 4,85
- Article number of the recommended special tool: V99-1020
- Axle alignment required after fitting
- Packaging width [cm]: 9,3
- Packaging height [cm]: 34,1
- Packaging Depth [cm]: 24
- Item number: V46-0115
- Manufacturer: VAICO
- EAN number: 4046001372810
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Fitting Position: Lower, Front Axle Left
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- Length [mm]: 329,5
- Cone Size [mm]: 18
- Trim Level: EXC. 1.6 RS
- Mounting points diameter [mm]: 12,2
- Rod / Strut: Push Rod
- Item number: SKCA-0051146
- Manufacturer: STARK
- EAN number: 4059191820788
- Condition: New
- Fitting Position: Lower, Front Axle Right
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- Length [mm]: 329,5
- Cone Size [mm]: 18
- Inner Diameter [mm]: 12,2
- Trim Level: EXC. 1.6 RS
- Rod / Strut: Push Rod
- Item number: SKCA-0051143
- Manufacturer: STARK
- EAN number: 4059191820726
- Condition: New
- Fitting Position: Front Axle Right, Lower
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 60 91 0894
- Supplementary Article / Supplementary Info Info 2: with bearing(s)
- Weight [kg]: 4,86
- Item number: 60 91 0895
- Manufacturer: SWAG
- EAN number: 4044688510358
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Fitting Position: Front Axle Left, Lower
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 60 91 0895
- Supplementary Article / Supplementary Info Info 2: with bearing(s)
- Weight [kg]: 4,86
- Item number: 60 91 0894
- Manufacturer: SWAG
- EAN number: 4044688510341
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Fitting Position: Front Axle Left
- Control / Trailing Arm Type: Control Arm
- paired article number: RE-WP-13710
- Supplementary Article / Supplementary Info Info 2: with rubber mount
- Packing Type: Box
- Packaging length [cm]: 61,2
- Packaging width [cm]: 34,4
- Packaging height [cm]: 8,8
- Item number: RE-WP-13709
- Manufacturer: MOOG
- EAN number: 4044197811779
- Condition: New
- Fitting Position: Front Axle Right
- Control / Trailing Arm Type: Control Arm
- paired article number: RE-WP-13709
- Supplementary Article / Supplementary Info Info 2: with rubber mount
- Packing Type: Box
- Packaging length [cm]: 61,2
- Packaging width [cm]: 34,4
- Packaging height [cm]: 8,8
- Item number: RE-WP-13710
- Manufacturer: MOOG
- EAN number: 4044197811786
- Condition: New
- Fitting Position: Front Axle Left, Front Axle, outer, Left, Lower
- Control / Trailing Arm Type: Control Arm
- paired article number: ZWD-RE-017
- Fabrication Number: ZWD-RE-016
- Item number: ZWD-RE-016
- Manufacturer: NTY
- EAN number: 590204889181
- Condition: New
- Fitting Position: Front Axle Right, Front Axle, outer, Right, Lower
- Control / Trailing Arm Type: Control Arm
- paired article number: ZWD-RE-016
- Fabrication Number: ZWD-RE-017
- Item number: ZWD-RE-017
- Manufacturer: NTY
- EAN number: 590204889180
- Condition: New
- Fitting Position: Front Axle Left, Lower
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 10895
- Supplementary Article / Supplementary Info Info 2: with bearing(s)
- Weight [kg]: 4,860
- Item number: 10894
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816108948
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Fitting Position: Front Axle Right, Lower
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 10894
- Supplementary Article / Supplementary Info Info 2: with bearing(s)
- Weight [kg]: 4,860
- Item number: 10895
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816108955
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Supplementary Info: Bosch-Mahle Turbo NEW
- Fitting Position: Front Axle Right, Lower
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 33105
- Supplementary Article / Supplementary Info Info 2: with ball joint, with bearing(s)
- Weight [kg]: 2,393
- Supplementary Article / Supplementary Info: with attachment material
- Item number: 33106
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816331063
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Supplementary Info: Bosch-Mahle Turbo NEW
- Fitting Position: Front Axle Left, Lower
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 33106
- Supplementary Article / Supplementary Info Info 2: with ball joint, with bearing(s)
- Weight [kg]: 2,393
- Supplementary Article / Supplementary Info: with attachment material
- Item number: 33105
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816331056
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Fitting Position: Front Axle Left
- Control / Trailing Arm Type: Control Arm
- paired article number: ZWD-RE-037
- Fabrication Number: ZWD-RE-036
- Item number: ZWD-RE-036
- Manufacturer: NTY
- EAN number: 590204811790
- Condition: New
- Fitting Position: Front Axle Right
- Control / Trailing Arm Type: Control Arm
- paired article number: ZWD-RE-036
- Fabrication Number: ZWD-RE-037
- Item number: ZWD-RE-037
- Manufacturer: NTY
- EAN number: 590204811791
- Condition: New
- Supplementary Info: ORIGINAL Quality
- Fitting Position: Front Axle Right
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 16-16 050 0056
- Supplementary Article / Supplementary Info Info 2: with ball joint, with rubber mount
- Required quantity: 1
- replacement in pairs recommended
- Item number: 16-16 050 0055
- Manufacturer: MEYLE
- EAN number: 4040074132845
- Condition: New
- Supplementary Info: ORIGINAL Quality
- Fitting Position: Front Axle Left
- Material: Sheet Steel
- Control / Trailing Arm Type: Control Arm
- paired article number: 16-16 050 0055
- Supplementary Article / Supplementary Info Info 2: with ball joint, with rubber mount
- Required quantity: 1
- replacement in pairs recommended
- Item number: 16-16 050 0056
- Manufacturer: MEYLE
- EAN number: 4040074132838
- Condition: New
- 1
- 2
- 3
- 4