Actual offers of Spark plug VW Transporter / Caravelle T3 Minibus 1.9 Syncro 78 hp Petrol DG
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: 686S0010
- Manufacturer: RIDEX
- EAN number: 4059191451371
- Condition: New
-
- Fuel Type: CNG / LPG
- Supplementary Article / Supplementary Info Info 2: Electrode gap must be set for operation on gas
- Replace after km: 15000
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Spark Plug: 1 - Earthed Electrode
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: 686S0012
- Manufacturer: RIDEX
- EAN number: 4059191685325
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8 mm
- Spark Plug: Connector Type M4, Nickel Middle Electrode, 3 - Earthed Electrode, Interference Suppression 1 kOhm, with gasket seat
- External Thread [mm]: 14,0
- Thread Length [mm]: 19,0
- Spark Position [mm]: 5,2
- Item number: 686S0035
- Manufacturer: RIDEX
- EAN number: 4059191685530
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: 686S0310
- Manufacturer: RIDEX
- EAN number: 4065739013994
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: 686S0069
- Manufacturer: RIDEX
- EAN number: 4059191571390
- Condition: New
-
- Engine Code: DG
- Fuel Type: CNG / LPG
- Required quantity: 4
- Spanner Size: 20.6
- Spark Plug: 1 - Earthed Electrode, Iridium Middle Electrode
- Thread Length [mm]: 19
- Thread Size: M14x1.25
- Tightening Torque [Nm]: 22
- Diameter [mm]: 14
- Item number: 686S0137
- Manufacturer: RIDEX
- EAN number: 4064138064613
- Condition: New
- Spanner Size: 20,8 mm
- Spark Plug: Connector Type M4, Nickel Middle Electrode, 3 - Earthed Electrode, Interference Suppression 1 kOhm, with gasket seat
- External Thread [mm]: 14,0
- Thread Length [mm]: 19,0
- Item number: 686S0319
- Manufacturer: RIDEX
- EAN number: 4065739014533
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 686S0070
- Manufacturer: RIDEX
- EAN number: 4059191571413
- Condition: New
-
- Fuel Type: CNG / LPG
- Supplementary Article / Supplementary Info Info 2: Electrode gap must be set for operation on gas
- Replace after km: 15000
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Spark Plug: 1 - Earthed Electrode
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: SKSP-1990011
- Manufacturer: STARK
- EAN number: 4059191393190
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8 mm
- Spark Plug: Connector Type M4, Nickel Middle Electrode, 3 - Earthed Electrode, Interference Suppression 1 kOhm, with gasket seat
- External Thread [mm]: 14,0
- Thread Length [mm]: 19,0
- Spark Position [mm]: 5,2
- Item number: SKSP-1990034
- Manufacturer: STARK
- EAN number: 4059191393473
- Condition: New
- Electrode Gap [mm]: 0,5
- Spanner Size: 20,8
- Thread Length [mm]: 9,5
- Spark Position [mm]: 1
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 20
- Number of pins: 1
- Item number: 0 241 229 560
- Manufacturer: BOSCH
- EAN number: 3165141048391
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: SKSP-1990009
- Manufacturer: STARK
- EAN number: 4059191393176
- Condition: New
-
- Construction Year from: 08 / 1987
- Construction Year to: 07 / 1989
- Electrode Gap [mm]: 0,76
- Spanner Size: 21
- Spark Plug: Nickel Middle Electrode, 1 - Earthed Electrode, Interference Suppression, with gasket seat, Control electrode gap
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3,30
- Thread Pitch [mm]: 1,25
- Connector type: SAE
- Weight [kg]: 0,07
- Resistor [kOhm]: 8
- Tightening torque from [Nm]: 20
- Tightening torque to [Nm]: 30
- Item number: 4263
- Manufacturer: AUTOLITE
- EAN number: 9100255334
- Condition: New
-
- Construction Year from: 08 / 1987
- Construction Year to: 07 / 1989
- Engine Code: DG,SP
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Spark Plug: 1 - Earthed Electrode
- Thread Length [mm]: 19
- Thread Size: M14 x 1,25
- Tightening Torque [Nm]: 28
- Assy. / disassy. by qualified personnel required!
- Item number: 8EH 188 704-171
- Manufacturer: HELLA
- EAN number: 4082300325461
- Condition: New
- Electrode Gap [mm]: 0,7
- Product line: Q+, original equipment manufacturer quality
- Spark Plug: 1 - Earthed Electrode
- Electrode gap to be set [mm]: 0,7
- Weight [kg]: 0,061
- Length [mm]: 126
- Packaging width [cm]: 8,5
- Packaging height [cm]: 2,4
- Packaging Depth [cm]: 2,4
- Item number: V99-75-0011
- Manufacturer: VEMO
- EAN number: 4046001273643
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Size: M 14 x 1,25
- Required quantity: 4
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 0 242 235 663
- Manufacturer: BOSCH
- EAN number: 3165143134085
- Condition: New
-
- Fuel Type: CNG / LPG
- Supplementary Article / Supplementary Info Info 2: Electrode gap must be set for operation on gas
- Replace after km: 15000
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 0 242 240 592
- Manufacturer: BOSCH
- EAN number: 3165143134429
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 21
- Spark Plug: with gasket seat, 3 - Earthed Electrode
- Thread Length [mm]: 19
- for OE number: 101 000 007 AD
- External Thread Size: M14 x 1,25
- Item number: 13508
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816135081
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Electrode Gap [mm]: 0,8
- Spanner Size: 21
- Spark Plug: with gasket seat, 3 - Earthed Electrode
- Thread Length [mm]: 19
- for OE number: 101 000 007 AD
- Item number: 13509
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816135098
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
- Electrode Gap [mm]: 0,9
- Product line: Q+, original equipment manufacturer quality
- Spark Plug: 3 - Earthed Electrode
- Electrode gap to be set [mm]: 0,7
- Weight [kg]: 0,06
- Packaging width [cm]: 8,5
- Packaging height [cm]: 2,4
- Packaging Depth [cm]: 2,4
- Item number: V99-75-0006
- Manufacturer: VEMO
- EAN number: 4046001250262
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- 1
- 2
- 3
- 4